Embedded Files
SUPERDEK
Superdek is a five (5) ribbed with rib height 27mm, designed in lightweight roll-formed profile using Japanese Technologies which provides extreme spanning capacity. With two extra lower ribs situated in the valley, it strengthens the profile with stronger visual effect and strength performance. The advantages of this profile help to save cost. This profile designed to perform a minimum recommended roof pitch 7° and has an effective coverage width of 760mm, with a rib height of 27mm. The ribs spaced are 190mm from center to center. Superdek is ideal for residential, industrial and commercial application. It can be also be used as permanent perimeter fencing for construction sites. With a capillary barrier on the upper lapping side of the female rib, it gives total weather protection.
SUPERSPAN
Superspan is a 7 ribbed, light weight roll formed profile which provides good quality spanning capacity. Its multiple ribs profile intensifies the performance of this roofing sheet. This profile is designed to perform a minimum recommended roof pitch 7° and has an effective coverage width of 760mm and ribs height of 17mm. The ribs spaced are 127mm from center to center. Superspan is designed especially for metal roofing and wall cladding application for residential, industrial, commercial and various types of buildings. With a capillary barrier on the upper lapping side of the female rib, it gives total weather protection.
SUPERTILE
Supertile is the latest and most advance technology that has been created to substitute other straight roofing profile. It has been introduced after the introduction of clay and concrete tile. Supertile is lighter than normal clay tile but much stronger since it comes in steel panels with steel fasteners to withstand harsh weather condition, yet it requires low structural support.
SUPERQLIP
SuperQlip ensures “trouble-free” installation as it was designed with interlock action rib to concealed clip fixing. Lightweight deigned and perform best to minimum 1.5 degree roof pitch, SuperQlip will withhold any weather condition with strong roofing and cladding system.
SUPER CRIMP CURVE
End Curve is produced from roll formed Superdek (5 ribbed) profile by crimping it to curve in order to provide versatility and creative refreshing look for buildings. It provides more area of flexibility. End Curve can reduce cost and minimize usage of flashing and gutters.
Full Curve
Full Curve is designed to change the shape of conventional roof. The minimum straight length of sheet at one end of a curve is 20mm and maximum length of curve can be crimp curve up to 9mm continuously without joining. Buildings will be given a softer appearance by the smooth full curve. It needs less supporting framework such as ridges and cladding with its smooth installation.
SUPER BATTEN
This is the 21st century design of roof truss system and economical alternative to the traditional timber roof battens. Super Batten is roll formed from high tensile Galvanized Steel and is conformed to JIS G3302 (Accurately roll-formed). By using high tensile galvanized steel, Super Batten is stringer, lighter and firmer than timber battens. Furthermore, it does not burn, damage, twist, fall apart, crack and rot easily. Super Batten can be lapped, saving precious time from cutting to length’s process to make a quicker and easier installation.
SUPER C-PURLIN
Super C-Purlin suitable for application on walls, tower structures, single bay buildings, and recessed roofs or building with custom shaped ground plans. It is also recommended on multiple bay building. Super C-Purlin can be used continuously over two or more span with the ends butted. This is to reduce deflection but they cannot be overlapped
FABRICATING/ BENDING OF ACCESSORIES
Fabricating process on truss installation is based on drawing requested. Accessories are required in steel truss system in order to connect all the trusses together. By joining the trusses together, the trusses will act as a whole structure hence increases it strength. There are a few kinds of truss accessories that are being used such as Apex Plate, Creeper Bracket, L Angle, L Plate, Hip Bracket, Anchor Bolt and Tek Screw. These parts are used sometimes in more than one application.
SGI™ STEEL TRUSS SYSTEM
This is specially designed to replace traditional timber support for roof and walling roofing sheet. Made from High Tensile Galvanized Steel of various thickness and conformed to JIS G3302. Its fully computer designed with proprietary software that is linked to sophisticated computer aided manufacturing which mean time saving, cost saving and precision engineering with consistent and remarkable quality.
Page updated
Google Sites
Report abuse